View OP200GPZ_7403762.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

dual low offset, low power operational amplifier data sheet op200 rev. e document feedback information furnished by analog dev ices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062 - 9106, u .s.a. tel: 781.329.4700 ? 1978 C 2012 analog devices, inc. all rights reserved. technical support www.anal og.com features low i nput o ffset v oltage: 75 v m ax imum low o ffset v oltage d rift, o ver ? 55 c < t a < +125 c 0.5 v/ c m ax imum low s upply c urrent ( p er a mplifier): 725 a m ax imum high o pen - l oop g ain: 5000 v/mv m in imum low i nput b ias current: 2 na m ax imum low n oise v oltage d ensity: 11 nv/hz at 1 khz stable with l arge c apacitive l oads: 10 nf t yp ical pin connections ?in a 1 +in a 2 nc 3 v? 4 out a 16 nc 15 nc 14 v+ 13 nc 5 nc 12 +in b 6 nc 1 1 ?in b 7 out b 10 nc 8 nc 9 nc = no connect 00322-001 figure 1. 16 - lead soic (s - suffix) out a 1 ?in a 2 +in a 3 v? 4 v+ 8 out b 7 ?in b 6 +in b 5 op200 00322-002 a b figure 2. 8- lead pdip (p - suffix) 8- lead cerdip (z - suffix) general description the op200 is the first monolithic dual operational amplifier to offer op77 type precision performance. available in the industry standard 8 - lead pinout, the op200 combines precision performance wit h the space and cost savings offered by a dual amplifier. the op200 features an extremely low input offset voltage of less than 75 v with a drift below 0.5 v/ c, guaranteed over the full military temperature range. open - loop gain of the op200 exceeds 5, 000,000 into a 10 k ? load; input bias current is under 2 na; cmrr is over 120 db ; and psrr is below 1.8 v/v. on - chip zener zap trimming is used to achieve the extremely low input offset voltage of the op200 and eliminates the need for offset pulling. powe r consumption of the op200 is low, with each amplifier drawing less than 725 a of supply current. the total current drawn by the dual op200 is less than one - half that of a single op07 , yet the op200 offers signi ficant improvements over this industry - standard op amp. the voltage noise density of the op200, 11 nv/ hz at 1 khz, is half that of most competitive devices. the op200 is pin compatible with the op221 , lm158, mc1458/ mc 1558, and lt1013. the op200 is an ideal choice for applications requiring multiple precision op amps and where low power consumption is critical. for a quad precision op amp, see the op400 .
op200 data shee t rev. e | page 2 of 16 table of contents features .............................................................................................. 1 pin connections ............................................................................... 1 general description ......................................................................... 1 revision history ............................................................................... 2 specifications ..................................................................................... 4 electrical characteristics ............................................................. 4 absolute maximum ratings ............................................................ 7 thermal resistance ...................................................................... 7 esd caution .................................................................................. 7 typical performance characteristics ............................................. 8 applications information .............................................................. 12 dual low power instrumentation amplifier ......................... 12 preci sion absolute value amplifier ......................................... 12 precision current pump ............................................................ 12 dual 12 - bit voltage output dac ............................................ 13 dual precision voltage reference ............................................ 13 programmable high resolution window comparator ........ 14 outline dimen sions ....................................................................... 15 ordering guide .......................................................................... 16 revision history 9 / 12 rev. d to rev. e change d table 2 conditions from v s = 15 v to v s = 15 v ...... 4 updated outline dimensions ....................................................... 15 cha nges to ordering guide .......................................................... 1 6 2/09 rev. c to rev. d change to large signal voltage gain, table 2 .............................. 4 changes to ordering guide .......................................................... 16 8 /08 rev. b to rev. c updated format .................................................................. universal changes to features section ............................................................ 1 changes to table 1 and table 2 ....................................................... 4 changes to table 3 and table 4 ....................................................... 5 deleted table 7; renumbered sequentially ................................... 5 changes to figure 15 ........................................................................ 9 changes to figure 21 ...................................................................... 10 changes to figure 30 and figure 31 ............................................. 12 changes to programmable high resolution window comparator section, figure 33, and figure 34 ........................... 13 changes to figure 35 ...................................................................... 1 4 updated outline dimensions ....................................................... 15 changes to ordering guide .......................................................... 16 2/04 data sheet changed from r ev . a to r ev . b. op200f d eleted .................................................................. universal changes to o rdering g uide ............................................................. 5 changes to figure 4 ........................................................................... 8 updated o utline d imension ........................................................ 11 4/02 data sheet changed from r ev . 0 to r ev . a. edits to f eatures ................................................................................. 1 edits to g eneral d escription ........................................................... 1 edits to o rdering i nformation ........................................................ 1 edits to p in c onnections .................................................................. 1 ed its to a bsolute m aximum r atings .............................................. 2 edits to p ackage t ype ....................................................................... 2
data sheet op200 rev. e | page 3 of 16 00322-003 +in voltage limiting network ?in bias out v? v+ figure 3. simplified schematic (one of two amplifier s shown )
op200 data shee t rev. e | page 4 of 16 specifications e lectrical c haracteristics v s = 15 v, t a = 25 c, unless otherwise noted. table 1 . parameter symbol conditions op200a/e op200g unit min typ max min typ max input characteristics input o ffset voltage v os 25 75 80 200 v long - term input voltage stability 0.1 0.1 v/mo input offset current i os v cm = 0 v 0.05 1.0 0.05 3.5 na input bias current i b v cm = 0 v 0.1 2.0 0.1 5.0 na input noise voltage e n p - p 0.1 hz to 10 hz 0.5 0.5 v p -p i nput noise voltage density 1 e n f o = 10 hz 22 36 22 nv/hz f o = 1000 hz 11 18 11 nv/hz input noise current i n p - p 0.1 hz to 10 hz 15 15 pa p -p input noise current density i n f o = 10 hz 0.4 0.4 pa/hz input resistance diff erential mode r in 10 10 m? input resistance common mode r incm 125 125 g? large signal voltage gain a vo v o = 10 v r l = 10 k ? 5000 12000 3000 7000 m/mv r l = 2 k? 2000 3700 1500 3200 m/mv 1 sample tested. v s = 15 v, ? 55 c t a + 125 c for op200a, unless otherwise noted. table 2 . parameter symbol conditions op200a unit min typ max input characteristics input offset voltage v os 45 125 v average input offset voltage drift tcv os 0.2 0 .5 v/c input offset current i os v cm = 0 v 0.15 2.5 na input bias current i b v cm = 0 v 0.9 5.0 na large signal voltage gain a vo v o = 10 v r l = 1 0 k ? 3000 9000 v/mv r l = 2 k? 1000 2700 v/mv input voltage range 1 ivr 12 1 2.5 v common - mode rejection ratio cmr r v cm = 12 v 115 130 db capacitive load stability a v = 1 8 nf power supply power supply rejection ratio psrr v s = 3 v to 18 v 0.2 3.2 v/v supply current per amplifier i sy no l oad 600 775 a output characteristics output voltage swing v o r l = 10 k ? 12 12.4 v r l = 2 k? 11 12 v 1 guaranteed by cmr r test.
data sheet op200 rev. e | page 5 of 16 v s = 15 v, t a = 25 c, unless otherwise noted. table 3 . parameter symbol conditions op200a/e op200g unit min typ max min typ max input characteristics input voltage range 1 ivr 12 13 12 13 v common - mode rejection ratio cmr r v cm = 12 v 120 135 110 130 db channel separation 2 cs v o = 20 v p -p , f o = 10 hz 123 145 1 23 145 db input capacitance c in 3.2 3.2 pf capacitive load stability a v = 1 , n o o scillations 10 10 nf power supply power supply rejection ratio psrr v s = 3 v to 18 v 0.4 1.8 0.6 5.6 v/v supply current per amplifier i sy no l oad 570 725 570 725 a output characteristics output voltage swing v o r l = 10 k? 12 12.6 12 12.6 v r l = 2 k? 11 12.2 11 12.2 v dynamic performance slew rate sr 0. 1 0.15 0.1 0.15 v/ s gain bandwidth product gb p a v = 1 500 500 khz 1 guaranteed by cmr r test. 2 guaranteed but not 100% tested. v s = 15 v, ? 40 c t a +85 c, unless otherwise noted. table 4 . parameter symbol conditions op200e op200g unit min typ max min typ m ax input characteristics input offset voltage v os 35 100 110 300 v average input offset voltage drift tcv os 0.2 0.5 0.6 2.0 v/c input offset current i os v cm = 0 v 0.08 2.5 0.1 6.0 na input bias current i b v cm = 0 v 0 3 5.0 0.5 10.0 na large - signal voltage gain a vo v o = 10 v r l = 10 k? 3000 10, 000 2000 5000 v/mv r l = 2 k? 1500 3200 1000 2500 v/mv input voltage range 1 ivr 12 12.5 12 12.5 v common - mode rejection ratio cmr r v cm = 12 v 115 130 105 130 db capacitive load stability a v = 1 , n o o scillations 10 10 nf power supply power supply rejection ratio psrr v s = 3 v to 18 v 0.15 3.2 0.3 10.0 v/v supply current per amplifier i sy no l oad 600 775 600 775 a output characteristics output voltage swing v o r l = 10 k? 12 12.4 12 12.4 v r l = 2 k? 11 12 11 12.2 v 1 guaranteed by cmr r test.
op200 data shee t rev. e | page 6 of 16 00322-004 v 2 v 1 20v p-p @ 10hz 50? channel separation = 20 log 50? v 1 v 2 /1000 1/2 op200 1/2 op200 figure 4. channel separation test circuit 00322-005 100? 10k? 1/2 op200 e out to spectrum analyzer e out (nv/hz) = 2 e out (nv/hz) 101 1/2 op200 figure 5. noise test schematic
data sheet op200 rev. e | page 7 of 16 absolute maximum rat ings table 5 . parameter rating supply voltage 20 v differential input voltage 30 v input voltage supply v oltage output short - circuit duration continuous storage temperature r ange ? 65c to +150c lead temperature (soldering, 60 sec) 300c junction temperature range (t j ) ? 65c to +150c operating temperature range op200a ? 55c to +125c op200e , op200 g ? 40c to +85c stresses above those listed under absolute maximum ratings m ay cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum r ating conditions for extended periods may affect device reliability. thermal resistance table 6 . package type ja 1 jc unit 8 - lead cerdip (z suffix ) 148 16 c/w 8 - lead plastic dip (p suffix ) 96 37 c/w 16- lead soic (s suffix ) 92 27 c/w 1 ja is specified for worst - case mounting conditions, that is , ja is specified for device in socket for cer dip and pdip packages; ja is specified for device soldered to printed circuit board for soic package. esd caution
op200 data shee t rev. e | page 8 of 16 typical performance characteristics 2 1 0 0 1.0 2.0 3.0 4.0 5.0 00322-006 change in offset voltage (v) time (minutes) t a = 25c v s = 15v figure 6. warm - up drift 10 20 30 40 50 60 0 ?75 ?50 ?25 0 25 50 75 100 125 00322-007 input offset voltage (v) temperature (c) v s = 15v figure 7. input offset voltage vs. temperature ?2 ?1 0 1 2 3 ?3 ?75 ?50 ?25 0 25 50 75 100 125 00322-008 input bias current (na) temperature (c) v s = 15v figure 8. input bias current vs. temperature 50 100 150 200 250 300 0 ?75 ?50 ?25 0 25 50 75 100 125 00322-009 input offset current (pa) temperature (c) v s = 15v figure 9. input offset current vs. temperature 0.2 0.4 0.6 0.8 1.0 0 ?15 ?10 ?5.0 0 5.0 10 15 00322-010 input bias current (na) comon-mode voltage (v) t a = 25c v s = 15v figure 10 . input bias current vs. common - mode voltage 20 40 60 80 100 120 140 0 1 10 100 1k 10k 100k 00322-011 common-mode rejection (db) frequency (hz) t a = 25c v s = 15v figure 11 . common - mode rejection vs. frequency
data sheet op200 rev. e | page 9 of 16 100 10 1 10 100 1k 00322-012 voltage noise density (nv/hz) frequency (hz) t a = 25c v s = 15v figure 12 . voltage noise density vs. frequency 1000 100 1 10 100 1k 00322-013 current noise density (fa/hz) frequency (hz) t a = 25c v s = 15v figure 13 . current noise density vs. frequency 0 2 4 6 8 10 00322-014 noise voltage (400nv/div) time (sec) figure 14 . 0.1 hz to 10 hz noise 1.18 1.06 1.08 1.10 1.12 1.14 1.16 2 6 10 14 18 00322-015 total supply current (ma) supply voltage (v) two amplifiers t a = 25c figure 15 . total supply current vs. supply voltage 1.16 1.11 1.12 1.13 1.14 1.15 ?75 ?50 ?25 0 25 50 75 100 125 00322-016 total supply current (ma) temperature (c) two amplifiers v s = 15v figure 16 . total supply current vs. temperature 140 0 20 40 60 80 100 120 0.1 1 10 100 1k 10k 100k 00322-017 power supply rejection (na) frequency (hz) t a = 25c positive supply negative supply figure 17 . power supply reje ction vs. frequency
op200 data shee t rev. e | page 10 of 16 0.7 0.1 0.2 0.3 0.4 0.5 0.6 ?75 ?50 00322-018 power supply rejection (v/v) temperature (c) ?25 0 25 50 75 100 125 figure 18 . power supply rejection vs. temperature 6000 0 1000 2000 3000 4000 5000 ?75 ?50 00322-019 open-loop gain (v/mv) temperature (c) ?25 0 25 50 75 100 125 v s = 15v r l = 2k? figure 19 . open - loop gain vs. temperature 140 ?2 0 0 20 60 40 80 100 120 10 100 1k 10k 100k 1m 00322-020 open-loop gain (db) frequency (hz) gain phase t a = 25c v s = 15v phase shift (degrees) 180 135 90 0 figure 20 . open - loop gain and phase shift vs. frequency 140 0 20 60 40 80 100 120 1 10 100 1k 10k 100k 1m 00322-021 closed-loop gain (db) frequency (hz) a v = 1000 a v = 100 a v = 10 a v = 1 t a = 25c v s = 15v figure 21 . closed - loop gain vs. frequency 30 0 5 10 15 20 25 10 100 1k 10k 100k 00322-022 output swing (v) frequency (hz) t a = 25c v s = 15v v p-p a t 1% dis t ortion figure 22 . maximum output swing vs. frequency 1 0.001 0.01 0.1 100 1k 10k 00322-023 total harmonic distortion (%) frequency (hz) t a = 25c v s = 15v v out = 10v p-p r l = 2k? a v = 1 a v = 10 a v = 100 figure 23 . total harmonic distortion vs. frequency
data sheet op200 rev. e | page 11 of 16 50 0 5 10 15 20 25 30 35 40 45 0 0.5 00322-024 overshoot (%) capacitive load (nf) 1.0 1.5 2.0 2.5 3.0 t a = 25c v s = 15v falling rising figure 24 . overshoot vs. capacitive load 29 22 23 24 25 26 27 28 0 1 00322-025 short-circuit current (ma) time (minutes) 2 3 4 5 t a = 25c v s = 15v sinking sourcing figure 25 . short - circuit current vs. time 150 90 100 110 120 130 140 10 100 1k 10k 100k 00322-026 channel separation (db) frequency (hz) figure 26 . channel separation vs. frequency 00322-027 t a = 25c v s = 15v a v = +1 100 s 5.00v figure 27 . large signal transient response 00322-028 t a = 25c v s = 15v a v = +1 5 s 20mv figure 28 . small signal transient response 00322-029 t a = 25c v s = 15v a v = +1 5 s 20mv figure 29 . small signal transient response , c load = 1 nf
op200 data shee t rev. e | page 12 of 16 a pplications i nformation the op200 is inherently stable at all gains and is capable of drivin g large capacitive loads without oscillating. nonetheless, good supply decoupling is highly recommended. proper supply decoupling reduces problems caused by supply line noise and improves the capacitive load driving capability of the op200. dual low power instrumentation amplifier a dual instrumentation amplifier that consumes less than 33 mw of power per channel is shown in figure 30 . the linearity of the instrumentation amplifier exceeds 16 bits in gains of 5 to 200 and is better than 14 bits in gains fr om 200 to 1000. cmrr is above 115 db (gain = 1000). offset voltage drift is typically 0.2 v/c over the military temperature range, which is comparable to the best monolithic instrumentation amplifiers. the bandwidth of the low power instrumentation ampli fier is a function of gain and is shown in table 7 . table 7 . gain bandwidth gain bandwidth 5 150 khz 10 67 khz 100 7.5 khz 1000 500 hz 00322-030 20k? 1 7 8 4 2 3 6 5 1/2 op200az 1/2 op200az v out v in v out = 5 + v in + v ref 40,000 r g ? + 5k? 5k? r g ?15v +15v v ref 20k? the output signal is specified with respect to the reference input, which is normally connected to analog ground. the reference input can be used to offset the output from ? 10 v to +10 v if required. precision absolute v alue ampli fier the circuit in figure 31 is a precision absolute value amplifier with an input impedance of 10 m. the high gain and low tcv os of the op200 ensure accurate operation with microvolt input signals. in this circuit, the input al ways appears as a common - mode signal to the op amps. the cmr r of the op200 exceeds 120 db, yielding an error of less than 2 ppm. 00322-031 r3 1k? r2 2k? 1/2 op200az 1/2 op200az v out 0v < v out < 10v r1 1k? c1 30pf d1 1n4148 d1 1n4148 7 1 8 4 6 5 2 3 v in ?15v +15v c2 0.1pf c2 0.1pf figure 31 . precision absolute value amplifier precision current pu mp the m aximum output current of t he precision current pump shown in figure 32 is 10 ma. voltage compliance is 10 v with 15 v supplies. output impedance of the current transmit - ter exceeds 3 m with linearity better than 16 bits. 00322-032 r5 100? 1 2 3 7 8 4 6 5 1/2 op200ez 1/2 op200ez i out v in i out = = 10ma/v = v in rs v in 100? ?15v +15v ? r1 10k? + r1 10k? r3 10k? r4 1k?
data sheet op200 rev. e | page 13 of 16 dual 12-bit voltage output dac the dual output dac shown in figure 33 is capable of providing untrimmed 12-bit accurate operation over the entire military temperature range. offset voltage, bias current, and gain errors of the op200 contribute less than 1/10 of an lsb error at 12 bits over the military temperature range. dual precision voltage reference a dual op200 and a ref43 , a 2.5 v reference, can be used to build a 2.5 v precision voltage reference. maximum output current from each reference is 10 ma with load regulation under 25 v/ma. line regulation is better than 15 v/v and output voltage drift is under 20 v/c. output voltage noise from 0.1 hz to 10 hz is typically 75 v p-p. r1 and d1 ensure correct startup. 00322-033 dac a 1/2 dac8221 dac8221 dac data bus pin 6 (msb) to pin 17 (lsb) 1/2 op200az 1/2 op200az out a v? out b r fb a v dd i out a r fb b i out b v ref a v ref b 2 6 1 8 4 7 3 3 21 4 22 2 23 24 agnd dgnd 1 5 18 19 20 10v reference voltage 5 v 5 dac b 1/2 dac8221 dac control dac a/dac b cs wr figure 33. dual 12-bit voltage output dac 0 0322-034 1/2 op200az ref43 v out trim gnd v in 1/2 op200az ?2.5v +2.5v ?5v r1 22k? d1 1n914 1 7 4 8 2 6 6 5 5 4 2 3 r3 10k? +5 v +5v r3 10k ? r4 5k ? figure 34. dual precision voltage reference
op200 data sheet rev. e | page 14 of 16 programmable high resolution window comparator the programmable window comparator shown in figure 35 is easily capable of 12-bit accuracy over the full military temperature range. a dual cmos 12-bit dac, the dac8221 , is used in the voltage switching mode to set the upper and lower thresholds (dac a and dac b, respectively). 00322-035 dac a 1/2 dac8221 dac data bus pin 6 (msb) to pin 17 (lsb) 1/2 op200az 1/2 op200az v ref a v dd v ref b i out a i out b 3 5 4 1 8 7 2 21 2 24 4 22 dgnd 18 19 20 10v reference voltage v in 15 v 6 dac b 1/2 dac8221 dac control signals dac a/dac b cs wr 5 agnd 1 r2 10k ? r1 10k ? d1 1n4148 d1 1n4148 q1 2n2222 r4 10k ? r2 10k ? ttl out 5v 15v? figure 35. programmable high resolution window comparator
data sheet op200 rev. e | page 15 of 16 outline dimensions controlling dimensions are in inches; millimeter dimensions (in parentheses) are rounded-off inch equivalents for reference only and are not appropriate for use in design. 0.310 (7.87) 0.220 (5.59) 0.005 (0.13) min 0.055 (1.40) max 0.100 (2.54) bsc 15 0 0.320 (8.13) 0.290 (7.37) 0.015 (0.38) 0.008 (0.20) seating plane 0.200 (5.08) max 0.405 (10.29) max 0.150 (3.81) min 0.200 (5.08) 0.125 (3.18) 0.023 (0.58) 0.014 (0.36) 0.070 (1.78) 0.030 (0.76) 0.060 (1.52) 0.015 (0.38) 14 5 8 figure 36. 8-lead ceramic dual in-line package [cerdip] (q-8) z-suffix dimensions shown in inches and (millimeters) compliant to jedec standards ms-001 controlling dimensions are in inches; millimeter dimensions (in parentheses) are rounded-off inch equivalents for reference only and are not appropriate for use in design. corner leads may be configured as whole or half leads. 070606-a 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) seating plane 0.015 (0.38) min 0.210 (5.33) max 0.150 (3.81) 0.130 (3.30) 0.115 (2.92) 0.070 (1.78) 0.060 (1.52) 0.045 (1.14) 8 1 4 5 0.280 (7.11) 0.250 (6.35) 0.240 (6.10) 0.100 (2.54) bsc 0.400 (10.16) 0.365 (9.27) 0.355 (9.02) 0.060 (1.52) max 0.430 (10.92) max 0.014 (0.36) 0.010 (0.25) 0.008 (0.20) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.195 (4.95) 0.130 (3.30) 0.115 (2.92) 0.015 (0.38) gauge plane 0.005 (0.13) min figure 37. 8-lead plastic dual in-line package [pdip] (n-8) p-suffix dimensions shown in inches and (millimeters)
op200 data sheet rev. e | page 16 of 16 controlling dimensions are in millimeters; inch dimensions (in parentheses) are rounded-off millimeter equivalents for reference only and are not appropriate for use in design. compliant to jedec standards ms-013-aa 10.50 (0.4134) 10.10 (0.3976) 0.30 (0.0118) 0.10 (0.0039) 2.65 (0.1043) 2.35 (0.0925) 10.65 (0.4193) 10.00 (0.3937) 7.60 (0.2992) 7.40 (0.2913) 0 . 7 5 ( 0 . 0 2 9 5 ) 0 . 2 5 ( 0 . 0 0 9 8 ) 45 1.27 (0.0500) 0.40 (0.0157) c oplanarity 0.10 0.33 (0.0130) 0.20 (0.0079) 0.51 (0.0201) 0.31 (0.0122) seating plane 8 0 16 9 8 1 1.27 (0.0500) bsc 03-27-2007-b figure 38. 16-lead standard small outline package [soic_w] wide body (rw-16) s-suffix dimensions shown in millimeters and (inches) ordering guide model 1 t a = 25c v os max (v) temperature range package description package option op200az 75 ?55c to +125c 8-lead cerdip z-suffix (q-8) op200ez 75 ?40c to +85c 8-lead cerdip z-suffix (q-8) OP200GPZ 200 ?40c to +85c 8-lead pdip p-suffix (n-8) op200gs 200 ?40c to +85c 16-lead soic_w s-suffix (rw-16) op200gsz 200 ?40c to +85c 16-lead soic_w s-suffix (rw-16) op200gsz-reel 200 ?40c to +85c 16-lead soic_w s-suffix (rw-16) 1 z = rohs compliant part. ?1978C2012 analog devices, inc. all rights reserved. trademarks and registered trademarks are the prop erty of their respective owners. d00322-0-9/12(e)

▲Up To Search▲

Price & Availability of OP200GPZ

	To Download OP200GPZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .